CXLE8854B wide input voltage, high efficiency CC and CV step-down DC/DC converter that operates in either CV (Constant Output Voltage) mode or CC (Constant Output Current) mode

目录zgE嘉泰姆

1.产品概述                       2.产品特点
3.应用范围                       4.下载产品资料PDF文档 
5.产品封装图</span>                     6.电路原理图</span>                   
7.功能概述                        8.相关产品zgE嘉泰姆

一,产品概述(General Description)         zgE嘉泰姆

    CXLE8854B is a wide input voltage, high efficiency CC and CV step-down DC/DC converter that operates in either CV (Constant Output Voltage) mode or CC (Constant Output Current) mode.
   CXLE8854B provides low-ripple power, high efficiency, and excellent transient characteristics.The PWM control circuit is able to the duty ratio linearly forms 0 up to 90%. An over current protection and short circuit protection functions are built outside that it can set by a resistance. An external compensation is easily to system stable;the low ESR output capacitor can be used.With the addition of an internal N-channel Power MOS, a coil, capacitors, and a diode connected externally, these ICs can function as step-down switching regulators.zgE嘉泰姆

    They serve as ideal power supply units for portable devices when coupled with the SOP-8L and SOP-8L-EP packages, providing such outstanding features as low current consumption. Since this converter can accommodate an input oltage up to 40V, it isalso suitable for the operation via an AC adapter
二</span>.产品特点(Features)zgE嘉泰姆

 Perfect Solution for Car Charger
Input Voltage：7V to 40V
High CC accuracy ±5%
High CV accuracy ±2%
Duty ratio：0% to 90% PWM control
Oscillation frequency：<br style="padding: 0px; margin: 0px;"/>120K Hz for  A
250K Hz for       B
Thermal Shutdown function.
Short Circuit Protect (SCP).
Built-in internal SW N-channel MOS.
Current mode non-synchronous PWM converter
Cycle to cycle Current Limiting
External current limit setting.
Under Voltage Lockout.
Over Voltage Protection.
三</span>,应用范围 (Applications)

四.下载产品资料PDF文档zgE嘉泰姆

 需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持</span>！</span>zgE嘉泰姆

 五</span>,产品封装图 (Package)

zgE嘉泰姆

六</span>.电路原理图</span>

七</span>,功能概述zgE嘉泰姆

As seen in Functional Block Diagram, the CXLE8854B is a peak current mode pulse width modulation
(PWM) converter with CC and CV control. The converter operates as follows:
A switching cycle starts when the rising edge of the Oscillator clock output causes thezgE嘉泰姆

High-Side Power Switch to turn on. With the SW side of the inductor now connected to Sense1, the inductor current ramps up to store energy in the magnetic field. The inductor current level is measured by the Current Sense Amplifier and added to the Oscillator ramp signal. If the resulting summation is higherthan the COMP voltage, the output of the PWM Comparator goes high. When this happens or when Oscillator clock output goes low, the High-Side Power Switch turns off.
At this point, the SW side of the inductor swings to a diode voltage below ground, causing the
inductor current to decrease and magnetic energy to be transferred to output. This state continues untilthe cycle starts again. The High-Side Power Switch is driven by logic using BS as the positive rail. This pin is charged to VSW + 5V when the Low-Side Power Switch turns on. The COMP voltage is the integration of the error between FB input and the internal 1V reference. If FB is lower than the reference voltage, COMP tends to go higher to increase current to the output. Output current will increase until it reaches the CC limit set by the R1 resistor. At this point, the device will transition from regulating output voltage to regulating output current, and the output voltage will drop with increasing load.
The Oscillator normally switches at 200KHz. However, if FB voltage is less than 0.45V, then the
switching frequency decreases until it reaches a typical value of 30KHz at VFB = 0.15V
八,相关产品                 更多同类产品......zgE嘉泰姆