CXSD62116A|B|C电压模式固定300kHz开关频率和同步降压控制器两个电源电压模式

目录PuB嘉泰姆

1.产品概述                       2.产品特点PuB嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 PuB嘉泰姆
5.产品封装图                     6.电路原理图                   PuB嘉泰姆
7.功能概述                        8.相关产品PuB嘉泰姆

一,产品概述(General Description)         PuB嘉泰姆
        The CXSD62116A/B/C is a voltage mode, fixed 300kHz-switching frequency,PuB嘉泰姆
and synchronous buck controller. The CXSD62116A/B/C allows wide input voltagePuB嘉泰姆
that is either a single 5~12V or two supply voltage(s) for various applications.PuB嘉泰姆
A power-on-reset (POR) circuit monitors the VCC supply voltage to preventPuB嘉泰姆
wrong logic controls. A built-in digital soft-start circuit prevents the outputPuB嘉泰姆
voltages from overshoot as well as limits the input current. An internalPuB嘉泰姆
0.6V temperature-compensated reference voltage with high accuracy isPuB嘉泰姆
designed to meet the requirement of low output voltage applications.PuB嘉泰姆
The CXSD62116A/B/C provides excellent output voltage regulations againstPuB嘉泰姆
load current variation.PuB嘉泰姆
     The controller’s over-current protection monitors the output currentPuB嘉泰姆
by using the voltage drops across the RDS(ON)of low-side MOSFET,PuB嘉泰姆
eliminating the need for a current sensing resistor that features highPuB嘉泰姆
efficiency and low cost.PuB嘉泰姆
     The CXSD62116A/B/C also integrates over-voltage protection (OVP) andPuB嘉泰姆
under-voltage protection circuit which moni-tors the FB voltage to preventPuB嘉泰姆
the PWM output from over and under voltage.PuB嘉泰姆
     The CXSD62116A/B/C is available in a simple SOP-8P package.PuB嘉泰姆
二.产品特点(Features)PuB嘉泰姆
Wide Operation Supply Voltage from 5V to 12VPuB嘉泰姆
Power-On-Reset Monitoring on VCC PuB嘉泰姆
Excellent Reference Voltage RegulationsPuB嘉泰姆
- 0.6V Internal ReferencePuB嘉泰姆
- ±1% Over Temperature RangePuB嘉泰姆
Integrated Soft-StartPuB嘉泰姆
Automatic PSM/PWM ModesPuB嘉泰姆
Voltage Mode PWM Operation with 90% (Max.) Duty CyclePuB嘉泰姆
Under-Voltage ProtectionPuB嘉泰姆
Adjustable Over-Current Protection ThresholdPuB嘉泰姆
- Sensing the RDS(ON) of Low-Side MOSFETPuB嘉泰姆
Over-Voltage ProtectionPuB嘉泰姆
Under-Voltage ProtectionPuB嘉泰姆
Simple SOP-8P PackagePuB嘉泰姆
Lead Free and Green Devices AvailablePuB嘉泰姆
(RoHS Compliant)PuB嘉泰姆
三,应用范围 (Applications)PuB嘉泰姆
Graphic CardsPuB嘉泰姆
DSL, Switch HUBPuB嘉泰姆
Wireless LanPuB嘉泰姆
Notebook ComputerPuB嘉泰姆
Mother BoardPuB嘉泰姆
LCD Monitor/TVPuB嘉泰姆

四.下载产品资料PDF文档 PuB嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！PuB嘉泰姆

 PuB嘉泰姆

五,产品封装图 (Package)PuB嘉泰姆
PuB嘉泰姆
六.电路原理图PuB嘉泰姆

PuB嘉泰姆
七,功能概述PuB嘉泰姆
Layout ConsiderationPuB嘉泰姆
In any high switching frequency converter, a correct lay-out is important to ensure proper operation of thePuB嘉泰姆
regulator. With power devices switching at 300kHz,the resulting current transient will cause voltage spike acrossPuB嘉泰姆
the interconnecting impedance and parasitic circuit elements. As an example, consider the turn-off transitionPuB嘉泰姆
of the PWM MOSFET. Before turn-off, the MOSFET is car rying the full load current. During turn-off, current stopsPuB嘉泰姆
flowing in the MOSFET and is free-wheeling by the lower MOSFET and parasitic diode. Any parasitic inductance ofPuB嘉泰姆
the circuit generates a large voltage spike during the switching interval. In general, using short and wide printedPuB嘉泰姆
circuit traces should minimize interconnecting imped-PuB嘉泰姆

Layout Consideration (Cont.)PuB嘉泰姆
ances and the magnitude of voltage spike. And signal and power grounds are to be kept separate till combinedPuB嘉泰姆

using ground plane construction or single point grounding. Figure 8. illustrates the layout, with bold linesPuB嘉泰姆
indicating high current paths; these traces must be short and wide. Components along the bold lines should bePuB嘉泰姆

placed lose together. Below is a checklist for your layout:PuB嘉泰姆

- Keep the switching nodes (UGATE, LGATE, and PHASE) away from sensitive small signal nodes since thesePuB嘉泰姆

nodes are fast moving signals. Therefore, keep traces to these nodes as short as possible.PuB嘉泰姆

- The traces from the gate drivers to the MOSFETs (UG and LG) should be short and wide.PuB嘉泰姆

- Place the source of the high-side MOSFET and the drain of the low-side MOSFET as close as possible. Minimiz-PuB嘉泰姆
ing the impedance with wide layout plane between the two pads reduces the voltage bounce of the node.PuB嘉泰姆
- Decoupling capacitor, compensation component, the resistor dividers, and boot capacitors should be closePuB嘉泰姆
their pins. (For example, place the decoupling ceramic capacitor near the drain of the high-side MOSFET asPuB嘉泰姆
close as possible. The bulk capacitors are also placed near the drain).PuB嘉泰姆
- The input capacitor should be near the drain of the up-per MOSFET; the output capacitor should be near thePuB嘉泰姆
loads. The input capacitor GND should be close to the output capacitor GND and the lower MOSFET GND.PuB嘉泰姆
- The drain of the MOSFETs (VIN and PHASE nodes) should be a large plane for heat sinking.PuB嘉泰姆
- The ROCSET resistance should be placed near the IC as close as possible.Close to ICPuB嘉泰姆
Figure 8. Layout GuidelinesPuB嘉泰姆

八,相关产品                     更多同类产品...... PuB嘉泰姆

Switching Regulator >   Buck ControllerPuB嘉泰姆

Part_No PuB嘉泰姆

Package PuB嘉泰姆

ArchiPuB嘉泰姆

tectuPuB嘉泰姆

PhasePuB嘉泰姆

No.ofPuB嘉泰姆

PWMPuB嘉泰姆

OutputPuB嘉泰姆

Output PuB嘉泰姆

CurrentPuB嘉泰姆

(A) PuB嘉泰姆

InputPuB嘉泰姆

Voltage (V) PuB嘉泰姆

ReferencePuB嘉泰姆

VoltagePuB嘉泰姆

(V) PuB嘉泰姆

Bias PuB嘉泰姆

VoltagePuB嘉泰姆

(V) PuB嘉泰姆

QuiescentPuB嘉泰姆

CurrentPuB嘉泰姆

(uA) PuB嘉泰姆

minPuB嘉泰姆

maxPuB嘉泰姆

CXSD6273PuB嘉泰姆

SOP-14PuB嘉泰姆

QSOP-16PuB嘉泰姆

QFN4x4-16PuB嘉泰姆

VM    PuB嘉泰姆

1   PuB嘉泰姆

1     PuB嘉泰姆

30PuB嘉泰姆

2.9    PuB嘉泰姆

13.2PuB嘉泰姆

0.9PuB嘉泰姆

12     PuB嘉泰姆

8000PuB嘉泰姆

CXSD6274PuB嘉泰姆

SOP-8PuB嘉泰姆

VM   PuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

20PuB嘉泰姆

2.9  PuB嘉泰姆

13.2 PuB嘉泰姆

0.8PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6274CPuB嘉泰姆

SOP-8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

20PuB嘉泰姆

2.9PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6275PuB嘉泰姆

QFN4x4-24PuB嘉泰姆

VMPuB嘉泰姆

2PuB嘉泰姆

1PuB嘉泰姆

60PuB嘉泰姆

3.1PuB嘉泰姆

13.2PuB嘉泰姆

0.6PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6276PuB嘉泰姆

SOP-8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

20PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

5~12PuB嘉泰姆

2100PuB嘉泰姆

CXSD6276APuB嘉泰姆

SOP-8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

20PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

5~12PuB嘉泰姆

2100PuB嘉泰姆

CXSD6277/A/BPuB嘉泰姆

SOP8|TSSOP8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

5PuB嘉泰姆

5PuB嘉泰姆

13.2PuB嘉泰姆

1.25|0.8PuB嘉泰姆

5~12PuB嘉泰姆

3000PuB嘉泰姆

CXSD6278PuB嘉泰姆

SOP-8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

10PuB嘉泰姆

3.3PuB嘉泰姆

5.5PuB嘉泰姆

0.8PuB嘉泰姆

5PuB嘉泰姆

2100PuB嘉泰姆

CXSD6279BPuB嘉泰姆

SOP-14PuB嘉泰姆

VM   PuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

10PuB嘉泰姆

5PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

12PuB嘉泰姆

2000PuB嘉泰姆

CXSD6280PuB嘉泰姆

TSSOP-24PuB嘉泰姆

|QFN5x5-32PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

2PuB嘉泰姆

20PuB嘉泰姆

5PuB嘉泰姆

13.2PuB嘉泰姆

0.6PuB嘉泰姆

5~12PuB嘉泰姆

4000PuB嘉泰姆

CXSD6281NPuB嘉泰姆

SOP14PuB嘉泰姆

QSOP16PuB嘉泰姆

QFN-16PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

30PuB嘉泰姆

2.9PuB嘉泰姆

13.2PuB嘉泰姆

0.9PuB嘉泰姆

12PuB嘉泰姆

4000PuB嘉泰姆

CXSD6282PuB嘉泰姆

SOP-14PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

30PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.6PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6282APuB嘉泰姆

SOP-14PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

30PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.6PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6283PuB嘉泰姆

SOP-14PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

25PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6284/APuB嘉泰姆

LQFP7x7 48PuB嘉泰姆

TQFN7x7-48PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

6PuB嘉泰姆

0.015PuB嘉泰姆

1.4PuB嘉泰姆

6.5PuB嘉泰姆

-PuB嘉泰姆

5PuB嘉泰姆

1800PuB嘉泰姆

CXSD6285PuB嘉泰姆

TSSOP-24PPuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

2PuB嘉泰姆

20PuB嘉泰姆

2.97PuB嘉泰姆

5.5PuB嘉泰姆

0.8PuB嘉泰姆

5~12PuB嘉泰姆

5000PuB嘉泰姆

CXSD6286PuB嘉泰姆

SOP-14PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

10PuB嘉泰姆

5PuB嘉泰姆

13.2PuB嘉泰姆

0.8PuB嘉泰姆

12PuB嘉泰姆

3000PuB嘉泰姆

CXSD6287PuB嘉泰姆

SOP-8-P|DIP-8PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

1PuB嘉泰姆

30PuB嘉泰姆

2.9PuB嘉泰姆

13.2PuB嘉泰姆

1.2PuB嘉泰姆

12PuB嘉泰姆

3000PuB嘉泰姆

CXSD6288PuB嘉泰姆

SSOP28PuB嘉泰姆

QFN4x4-24PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

2PuB嘉泰姆

20PuB嘉泰姆

5PuB嘉泰姆

24PuB嘉泰姆

0.9PuB嘉泰姆

5PuB嘉泰姆

1200PuB嘉泰姆

CXSD6289PuB嘉泰姆

SOP-20PuB嘉泰姆

VMPuB嘉泰姆

1PuB嘉泰姆

2PuB嘉泰姆

20PuB嘉泰姆

2.2PuB嘉泰姆

13.2PuB嘉泰姆

0.6PuB嘉泰姆

5~12PuB嘉泰姆

4000PuB嘉泰姆

CXSD6290PuB嘉泰姆