CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

发布时间:2020-04-21 16:28:53 浏览次数:392 作者:oumao18 来源:嘉泰姆
摘要:CXSD6276A控制器的过电流保护监视输出 通过使用低压侧MOSFET的RDS(ON)上的电压降得到的电流, 不需要电流感应电阻器。附加欠压和 过电压保护监视FB引脚上的电压是否短路和 过电压保护。过电流保护使软起动循环 起作用,直到4个过电流事件被计数。拉并保持电压 在低于0.15V的OCSET引脚上,使用开放式排水装置关闭控制器
CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

目录Ins嘉泰姆

1.产品概述                       2.产品特点Ins嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 Ins嘉泰姆
5.产品封装图                     6.电路原理图                   Ins嘉泰姆
7.功能概述                        8.相关产品Ins嘉泰姆

一,产品概述(General Description)     Ins嘉泰姆


  The CXSD6276 CXSD6276A is a fixed 300kHz frequency, voltage mode, andIns嘉泰姆
synchronous PWM controller. The device drives two low cost N-channelIns嘉泰姆
MOSFETs and is de-signed to work with single 5~12V or two supplyIns嘉泰姆
voltage(s), providing excellent regulation for load transients.Ins嘉泰姆
 The CXSD6276 CXSD6276A integrates controls, monitoring, and protection functionsIns嘉泰姆
into a single 8-pin package to provide a low cost and perfect power solution.Ins嘉泰姆
A power-on-reset (POR) circuit monitors the VCC supply voltage to preventIns嘉泰姆
wrong logic controls. An internal 0.8V reference provides low output voltageIns嘉泰姆
down to 0.8V for further applications. An built-in digital soft-start with fixedIns嘉泰姆
soft-start interval prevents the output voltage from overshoot as well as limitsIns嘉泰姆
the input current. The controller’s over-current protection monitors the outputIns嘉泰姆
current by using the voltage drop across the low-side MOSFET’s RDS(ON),Ins嘉泰姆
eliminating the need of a current sensing resistor. Additional under voltage andIns嘉泰姆
over voltage protections monitor the voltage on FB pin for short-circuit andIns嘉泰姆
over-voltage protections. The over-current protection cycles the soft-startIns嘉泰姆
function until 4 over-current events are counted.Pulling and holding the voltageIns嘉泰姆
on OCSET pin below 0.15V with an open drain device shuts down the controller.Ins嘉泰姆
二.产品特点(Features)Ins嘉泰姆


1.)Operating with Single 5~12V Supply VoltageIns嘉泰姆
2.)or Two Supply VoltagesIns嘉泰姆
3.)Drive Dual Low Cost N-Channel MOSFETsIns嘉泰姆
     Adaptive Shoot-Through ProtectionIns嘉泰姆
4.)Built-in Feedback CompensationIns嘉泰姆
    Voltage-Mode PWM ControlIns嘉泰姆
    0~100% Duty RatioIns嘉泰姆
     Fast Transient ResponseIns嘉泰姆
5.)±2% 0.8V ReferenceIns嘉泰姆
    Over Line, Load Regulation, and Operating   Ins嘉泰姆
6.)Temperature Programmable Over-Current ProtectionIns嘉泰姆
   Using RDS(ON) of Low-Side MOSFETIns嘉泰姆
7.)Hiccup-Mode Under-Voltage ProtectionIns嘉泰姆
8.)118% Over-Voltage ProtectionIns嘉泰姆
9.)Adjustable Output VoltageIns嘉泰姆
10.)Small Converter SizeIns嘉泰姆
      300kHz Constant Switching FrequencyIns嘉泰姆
      Small SOP-8 PackageIns嘉泰姆
11.)Built-In Digital Soft-StartIns嘉泰姆
12.)Shutdown Control Using an External MOSFETIns嘉泰姆
13.)Lead Free and Green Devices AvailableIns嘉泰姆
三,应用范围 (Applications)Ins嘉泰姆


MotherboardIns嘉泰姆
Graphics CardIns嘉泰姆
High Current, up to 20A, DC-DC ConvertersIns嘉泰姆
四.下载产品资料PDF文档 Ins嘉泰姆


需要详细的PDF规格书请扫一扫微信联系我们,还可以获得免费样品以及技术支持Ins嘉泰姆

 QQ截图20160419174301.jpgIns嘉泰姆

五,产品封装图 (Package)Ins嘉泰姆

Ins嘉泰姆

BOOT (Pin 1)Ins嘉泰姆

This pin provides ground referenced bias voltage to the high-side MOSFET driver. A bootstrap circuit with a diode connected to 5~12V is used to create a voltage suitable to drive a logic-level N-channel MOSFET.Ins嘉泰姆
UGATE (Pin 2)Ins嘉泰姆
Connect this pin to the high-side N-channel MOSFET’s gate. This pin provides gate drive for the high-side MOSFET.Ins嘉泰姆
GND (Pin 3)Ins嘉泰姆
The GND terminal provides return path for the IC’s biascurrent and the low-side MOSFET driver’s pull-low current. Connect the pin to the system ground via very low impedance layout on PCBs.Ins嘉泰姆
LGATE (Pin 4)Ins嘉泰姆
Connect this pin to the low-side N-channel MOSFET’s gate. This pin provides gate drive for the low-side MOSFET. Ins嘉泰姆
VCC (Pin 5)Ins嘉泰姆
Connect this pin to a 5~12V supply voltage. This pin provides bias supply for the control circuitry and the low-side MOSFET driver. The voltage at this pin is monitored for the Power-On-Reset (POR) purpose. Ins嘉泰姆
FB (Pin 6)Ins嘉泰姆
This pin is the inverting input of the internal Gm amplifier.Connect this pin to the output (VOUT) of the converter via an external resistor divider for closed-loop operation.The output voltage set by the resistor divider is deter-mined using the following formula :Ins嘉泰姆
where R1 is the resistor connected from VOUT to FB ,and R2 is the resistor connected from FB to GND. The FB pin is also monitored for under and over-voltage events. Ins嘉泰姆
OCSET (Pin 7)Ins嘉泰姆
The OCSET is a dual-function input pin for over-current protection and shutdown control. Connect a resistor (ROCSET) from this pin to the Drain of the low-side MOSFET. This resistor, an internal 40μA current source (IOCSET), and the MOSFET’s on-resistance(RDSON) set the converter over-current trip level (IPEAK) according to the following formula:Ins嘉泰姆
Pulling and holding this pin below 0.15V with an open drain device, with very low parasitic capacitor, shuts down the IC with floating output and also resets the over-current counter. Releasing OCSET pin initiates a new soft-start and the converter works again.Ins嘉泰姆
PHASE (Pin 8) Ins嘉泰姆
The pin provides return path for the high-side MOSFETdriver’s pull-low current. Connect this pin to the high-side MOSFET’s sourceIns嘉泰姆
六.电路原理图Ins嘉泰姆
blob.pngIns嘉泰姆
七,功能概述Ins嘉泰姆
Power-On-Reset (POR) Ins嘉泰姆
The CXSD6276 monitors the VCC voltage (V CC) for Power-On-Reset function, preventing wrong logic operation during powering on. When the VCC voltage is ready, the CXSD6276 starts a start-up process and then ramps the output voltage up to the target voltage. Ins嘉泰姆
Soft-StartIns嘉泰姆
The CXSD6276 has a built-in digital soft-start to control the output voltage rise and limit the current surge at the start-up. During the soft-start, an internal ramp con-nected to the one of the positive inputs of the Gm amplifier rises up from 0V to 2V to replace the reference voltage (0.8V) until the ramp voltage reaches the refer-Ins嘉泰姆
ence voltage. The soft-start interval is about 3.2mstypical, independent of the converter’s input and out-put voltages.Ins嘉泰姆
Over-Current Protection (OCP)Ins嘉泰姆
The over-current function protects the switching c o nverter against over-current or short-circuit conditions. The controller senses the inductor current by detecting the drain-to-source voltage, product of the inductor’s current and the on-resistance, of the low-side MOSFET during it’s on-state. This method enhances the converter’s efficiency and reduces cost by eliminating a current sensing resistor.A resistor (ROCSET), connected from the OCSET to theIns嘉泰姆
Over-Current Protection (OCP) (Cont.)Ins嘉泰姆
low-side MOSFET’s drain, programs the over-current trip level. An internal 40μA (typical) current source flowing through the ROCSET develops a voltage (VROCSET) across the ROCSET. When the VOCSET Ins嘉泰姆

八,相关产品                更多同类产品...... Ins嘉泰姆


Switching Regulator >   Buck ControllerIns嘉泰姆

Part_No Ins嘉泰姆

Package Ins嘉泰姆

ArchiIns嘉泰姆

tectuIns嘉泰姆

PhaseIns嘉泰姆

No.ofIns嘉泰姆

PWMIns嘉泰姆

OutputIns嘉泰姆

Output Ins嘉泰姆

CurrentIns嘉泰姆

(A) Ins嘉泰姆

InputIns嘉泰姆

Voltage (V) Ins嘉泰姆

ReferenceIns嘉泰姆

VoltageIns嘉泰姆

(V) Ins嘉泰姆

Bias Ins嘉泰姆

VoltageIns嘉泰姆

(V) Ins嘉泰姆

QuiescentIns嘉泰姆

CurrentIns嘉泰姆

(uA) Ins嘉泰姆

minIns嘉泰姆

maxIns嘉泰姆

CXSD6273Ins嘉泰姆

SOP-14Ins嘉泰姆

QSOP-16Ins嘉泰姆

QFN4x4-16Ins嘉泰姆

VM    Ins嘉泰姆

1   Ins嘉泰姆

1     Ins嘉泰姆

30Ins嘉泰姆

2.9    Ins嘉泰姆

13.2Ins嘉泰姆

0.9Ins嘉泰姆

12     Ins嘉泰姆

8000Ins嘉泰姆

CXSD6274Ins嘉泰姆

SOP-8Ins嘉泰姆

VM   Ins嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

20Ins嘉泰姆

2.9  Ins嘉泰姆

13.2 Ins嘉泰姆

0.8Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6274CIns嘉泰姆

SOP-8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

20Ins嘉泰姆

2.9Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6275Ins嘉泰姆

QFN4x4-24Ins嘉泰姆

VMIns嘉泰姆

2Ins嘉泰姆

1Ins嘉泰姆

60Ins嘉泰姆

3.1Ins嘉泰姆

13.2Ins嘉泰姆

0.6Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6276Ins嘉泰姆

SOP-8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

20Ins嘉泰姆

2.2Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

5~12Ins嘉泰姆

2100Ins嘉泰姆

CXSD6276AIns嘉泰姆

SOP-8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

20Ins嘉泰姆

2.2Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

5~12Ins嘉泰姆

2100Ins嘉泰姆

CXSD6277/A/BIns嘉泰姆

SOP8|TSSOP8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

5Ins嘉泰姆

5Ins嘉泰姆

13.2Ins嘉泰姆

1.25|0.8Ins嘉泰姆

5~12Ins嘉泰姆

3000Ins嘉泰姆

CXSD6278Ins嘉泰姆

SOP-8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

10Ins嘉泰姆

3.3Ins嘉泰姆

5.5Ins嘉泰姆

0.8Ins嘉泰姆

5Ins嘉泰姆

2100Ins嘉泰姆

CXSD6279BIns嘉泰姆

SOP-14Ins嘉泰姆

VM   Ins嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

10Ins嘉泰姆

5Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

12Ins嘉泰姆

2000Ins嘉泰姆

CXSD6280Ins嘉泰姆

TSSOP-24Ins嘉泰姆

|QFN5x5-32Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

2Ins嘉泰姆

20Ins嘉泰姆

5Ins嘉泰姆

13.2Ins嘉泰姆

0.6Ins嘉泰姆

5~12Ins嘉泰姆

4000Ins嘉泰姆

CXSD6281NIns嘉泰姆

SOP14Ins嘉泰姆

QSOP16Ins嘉泰姆

QFN-16Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

30Ins嘉泰姆

2.9Ins嘉泰姆

13.2Ins嘉泰姆

0.9Ins嘉泰姆

12Ins嘉泰姆

4000Ins嘉泰姆

CXSD6282Ins嘉泰姆

SOP-14Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

30Ins嘉泰姆

2.2Ins嘉泰姆

13.2Ins嘉泰姆

0.6Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6282AIns嘉泰姆

SOP-14Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

30Ins嘉泰姆

2.2Ins嘉泰姆

13.2Ins嘉泰姆

0.6Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6283Ins嘉泰姆

SOP-14Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

25Ins嘉泰姆

2.2Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6284/AIns嘉泰姆

LQFP7x7 48Ins嘉泰姆

TQFN7x7-48Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

6Ins嘉泰姆

0.015Ins嘉泰姆

1.4Ins嘉泰姆

6.5Ins嘉泰姆

-Ins嘉泰姆

5Ins嘉泰姆

1800Ins嘉泰姆

CXSD6285Ins嘉泰姆

TSSOP-24PIns嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

2Ins嘉泰姆

20Ins嘉泰姆

2.97Ins嘉泰姆

5.5Ins嘉泰姆

0.8Ins嘉泰姆

5~12Ins嘉泰姆

5000Ins嘉泰姆

CXSD6286Ins嘉泰姆

SOP-14Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

10Ins嘉泰姆

5Ins嘉泰姆

13.2Ins嘉泰姆

0.8Ins嘉泰姆

12Ins嘉泰姆

3000Ins嘉泰姆

CXSD6287Ins嘉泰姆

SOP-8-P|DIP-8Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

1Ins嘉泰姆

30Ins嘉泰姆

2.9Ins嘉泰姆

13.2Ins嘉泰姆

1.2Ins嘉泰姆

12Ins嘉泰姆

3000Ins嘉泰姆

CXSD6288Ins嘉泰姆

SSOP28Ins嘉泰姆

QFN4x4-24Ins嘉泰姆

VMIns嘉泰姆

1Ins嘉泰姆

2Ins嘉泰姆

20Ins嘉泰姆

5Ins嘉泰姆

24Ins嘉泰姆

0.9Ins嘉泰姆

发表评论

共有条评论
用户名: 密码:
验证码: 匿名发表

AI 智能助手