CXSD61051 synchronous step down regulator CC control from a high voltage input supply 3.5A continuou

目录10x嘉泰姆

1.产品概述                       2.产品特点10x嘉泰姆
3.应用范围                       4.产品封装图10x嘉泰姆
5.电路原理图                   6.产品PCB                   10x嘉泰姆
7.产品BOM                      8.产品PDF文档 10x嘉泰姆
9.功能概述                      10.相关产品10x嘉泰姆

 10x嘉泰姆

一,产品概述(General Description)   10x嘉泰姆

        The CXSD61051 is a synchronous step down regulator with CC control from a high voltage input supply. Operating with an input voltage10x嘉泰姆
range of 8V ～ 30V, the CXSD61051 achieves 3.5A continuous output current with excellent load and line regulation. The switching  frequency is programmable from 100KHz to 500KHz and the synchronous architecture10x嘉泰姆
provides for highly efficient designs. Current  mode operation provides fast transient response and eases loop stabilization.10x嘉泰姆

         The CXSD61051 requires a minimum number of readily available standard external components. Other features include cable compensation programmable current limit and thermal shutdown.10x嘉泰姆

        The CXSD61051 converters are available in the industry standard SOP8-PP packages       10x嘉泰姆

二.产品特点(Features)10x嘉泰姆

Wide Input Voltage Range: 8V ～ 30V10x嘉泰姆

Up to 93% Efficiency10x嘉泰姆

Programmable Switching Frequency up to 500KHz10x嘉泰姆

No Loop Compensation Required10x嘉泰姆

CC/CV control10x嘉泰姆

Programmable CC Current10x嘉泰姆

Thermal Shutdown10x嘉泰姆

Available in SOP8-PP Package10x嘉泰姆

三,应用范围 (Applications) 10x嘉泰姆

Car Charger / Adaptor10x嘉泰姆

LED Driver10x嘉泰姆

Pre-Regulator for Linear Regulators10x嘉泰姆

Distributed Power Systems10x嘉泰姆

Battery ChargerCar Charger / Adaptor10x嘉泰姆

LED Driver10x嘉泰姆

Pre-Regulator for Linear Regulators10x嘉泰姆

Distributed Power Systems10x嘉泰姆

Battery Charger10x嘉泰姆

四,产品封装图 (Package)10x嘉泰姆
10x嘉泰姆

五,电路原理图10x嘉泰姆

10x嘉泰姆

六, 产品PCB10x嘉泰姆
(略)10x嘉泰姆
七.产品BOM  10x嘉泰姆
  (略)10x嘉泰姆
八.产品PDF文档 10x嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！10x嘉泰姆

 10x嘉泰姆

九,功能概述10x嘉泰姆

Application Information 10x嘉泰姆
The CXSD61051 operates by a constant frequency, current mode architecture. The output voltage is set10x嘉泰姆
by an external divider returned to the FB pin. An error amplifier compares the divided output voltage with10x嘉泰姆
a reference voltage of 1.21V and adjusts the peak inductor current accordingly. 10x嘉泰姆
Thermal Protection10x嘉泰姆
The total power dissipation in CXSD61051 is limited by a thermal protection circuit. When the device10x嘉泰姆
temperature rises to approximately +160°C, this circuit turns off the output, allowing the IC to cool. The10x嘉泰姆
thermal protection circuit can protect the device from being damaged by overheating in the event of fault10x嘉泰姆
conditions. Continuously running the CXSD61051 into thermal shutdown degrades device reliability. 10x嘉泰姆
Current Limit10x嘉泰姆
Current limit detection occurs during the off-time by monitoring the current through the low-side switch10x嘉泰姆
using an external resistor, RLIM. The current limit value is defined by RLIM. If during the off-time the10x嘉泰姆
current in the low-side switch exceeds the user defined current limit value, the next on-time cycle is10x嘉泰姆
immediately terminated. Current sensing is achieved by comparing the voltage across the low side FET10x嘉泰姆
with the voltage across the current limit set resistor RLIM. For example, the current limit value is 4.5A by10x嘉泰姆
the RLIM =100K. The current limit value rises when the set resistor RLIM rises. The maximum output10x嘉泰姆
current is set by RLIM: RLIM (kΩ) = 1500 · IMAX (A) / RDS_PMOS (mΩ). 10x嘉泰姆
Oscillator Frequency10x嘉泰姆
The CXSD61051 oscillator frequency is set by a single external resistor connected between the RT pin and10x嘉泰姆
the GND pin. The resistor should be located very close to the device and connected directly to the pins10x嘉泰姆
of the IC (RT and GND). An internal amplifier holds the RT pin at a fixed voltage typically 0.6V. The10x嘉泰姆
oscillator frequency rises when the resistor RT falls. To determine the timing resistance for a given10x嘉泰姆
switching frequency, use the equation below:10x嘉泰姆
RT(kΩ)= 22000 /fOSC(kHz) 10x嘉泰姆
Setting Output Voltage10x嘉泰姆
The output voltage is set with a resistor divider from the output node to the FB pin. It is recommended to10x嘉泰姆
use divider resistors with 1% tolerance or better. To improve efficiency at very light loads consider using10x嘉泰姆
larger value resistors. If the values are too high the regulator is more susceptible to noise and voltage10x嘉泰姆
errors from the FB input current are noticeable. For most applications, a resistor in the 10kΩ to 1MΩ10x嘉泰姆
range is suggested for R3. R2 is then given by:10x嘉泰姆
R2 = R3 · [(VOUT / VREF) – 1]10x嘉泰姆
where VREF is 1.21V.10x嘉泰姆
Output Cable Resistance Compensation10x嘉泰姆
To compensate for resistive voltage drop across the charger's output cable, the CXSD61051 integrates a10x嘉泰姆
simple, user-programmable cable voltage drop compensation using the impedance at the FB pin.10x嘉泰姆
Choose the proper feedback resistance values for cable compensation refer to the curve in Figure 1.10x嘉泰姆
The delta VOUT voltage rises when the feedback resistance R3 value rises, use the equation below10x嘉泰姆
十,相关产品              更多同类产品......10x嘉泰姆