• [ CXSD62115 ]

样品申请

目录qBJ嘉泰姆

1.产品概述                       2.产品特点qBJ嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 qBJ嘉泰姆
5.产品封装图                     6.电路原理图                   qBJ嘉泰姆
7.功能概述                        8.相关产品qBJ嘉泰姆

一,产品概述(General Description)    qBJ嘉泰姆

  The CXSD62115, two-phase PWM control IC, provides a precision voltage regulation system for advanced graphic microprocessors in graphics card applications. The inte-gration of power MOSFET drivers into the controller ICqBJ嘉泰姆
reduces the number of external parts for a cost and space saving power management solution.qBJ嘉泰姆
  The CXSD62115 uses a voltage-mode PWM architecture,operating with fixed-frequency, to provide excellent load transient response. The device uses the voltage across the DCRs of the inductors for current sensing. Load lineqBJ嘉泰姆
voltage positioning (DROOP), channel-current balance,and over-current protection are accomplished through continuous inductor DCR current sensing.qBJ嘉泰姆
The MODE pin programs single- or two- phase operation.When IC operates in two-phase mode normally, it can transfer two-phase mode to single phase mode at liberty.Nevertheless, once operates in single-phase mode, the operation mode is latched. It is required to toggle SS or 5VCC pin to reset the IC. Such feature of the MODE pin makes the CXSD62115 ideally suitable for dual power input applications, such as PCIE interfaced graphic cards. This control IC‘s protection features include a set of so- phisticated over-temperature, over-voltage, under-voltage, and over-current protections. Over-voltage results in the converter turning the lower MOSFETs on to clamp the rising output voltage and protects the microprocessor.The over-current protection level is set through externalresistors. The device also provides a power-on-reset func-tion and a programmable soft-start to prevent wrong op-eration and limit the input surge current during power-on or start-up.qBJ嘉泰姆
 The CXSD62115 is available in a QFN4x4-24A packageqBJ嘉泰姆
二.产品特点(Features)qBJ嘉泰姆

Voltage-Mode Operation with Current SharingqBJ嘉泰姆
- Adjustable Feedback CompensationqBJ嘉泰姆
- Fast Load Transient ResponseqBJ嘉泰姆
Operate with 8V~13.2 VCC Supply VoltageqBJ嘉泰姆
Programmable 3-Bit DAC ReferenceqBJ嘉泰姆
-±1.5% System Accuracy Over-TemperatureqBJ嘉泰姆
Support Single- and Two-Phase OperationsqBJ嘉泰姆
5V Linear Regulator Output on 5VCCqBJ嘉泰姆
8~12V Gate Drivers with Internal Bootstrap DiodeqBJ嘉泰姆
Lossless Inductor DCR Current SensingqBJ嘉泰姆
Fixed 300kHz Operating Frequency Per PhaseqBJ嘉泰姆
Power-OK Indicator OutputqBJ嘉泰姆
- Regulated 1.5V on POKqBJ嘉泰姆
Adjustable Over-Current Protection (OCP)qBJ嘉泰姆
Accurate Load Line (DROOP) ProgrammingqBJ嘉泰姆
Adjustable Soft-StartqBJ嘉泰姆
Over-Voltage Protection (OVP)qBJ嘉泰姆
Under-Voltage Protection (UVP)qBJ嘉泰姆
Over-Temperature Protection (OTP)qBJ嘉泰姆
QFN4x4 24-Lead Package (QFN4x4-24A)qBJ嘉泰姆
Lead Free and Green Devices AvailableqBJ嘉泰姆
(RoHS Compliant)qBJ嘉泰姆
三,应用范围 (Applications)qBJ嘉泰姆

Graphics Card GPU Core Power SupplyqBJ嘉泰姆

Motherboard Chipset or DDR SDRAM Core Power SupplyqBJ嘉泰姆
On-Board High Power PWM Converter withqBJ嘉泰姆

Output Current up to 60AqBJ嘉泰姆
四.下载产品资料PDF文档 qBJ嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！qBJ嘉泰姆

 qBJ嘉泰姆

五,产品封装图 (Package)qBJ嘉泰姆

qBJ嘉泰姆

qBJ嘉泰姆
qBJ嘉泰姆

六.电路原理图qBJ嘉泰姆

qBJ嘉泰姆

七,功能概述qBJ嘉泰姆

Layout Consideration qBJ嘉泰姆

In any high switching frequency converter, a correct lay-out is important to ensure proper operation of theqBJ嘉泰姆
regulator. With power devices switching at higher frequency, the resulting current transient will cause volt-qBJ嘉泰姆
age spike across the interconnecting impedance and parasitic circuit elements. As an example, consider theqBJ嘉泰姆
turn-off transition of the PWM MOSFET. Before turn-off condition, the MOSFET is carrying the full load current.qBJ嘉泰姆
During turn-off, current stops flowing in the MOSFET and is freewheeling by the lower MOSFET and parasitic diode.qBJ嘉泰姆
Any parasitic inductance of the circuit generates a large voltage spike during the switching interval. In general,qBJ嘉泰姆
using short and wide printed circuit traces should mini-mize interconnecting impedances and the magnitude ofqBJ嘉泰姆
voltage spike. And signal and power grounds are to be kept separating and finally combined to use the groundqBJ嘉泰姆
plane construction or single point grounding. The best tie-point between the signal ground and the power ground is at the negative side of the output capacitor on each channel, where there is less noise. Noisy traces beneath the IC are not recommended. Below is a checklist for your layout:qBJ嘉泰姆
close their pins. (For example, place the decoupling ce-ramic capacitor near the drain of the high-side MOSFETqBJ嘉泰姆
as close as possible. The bulk capacitors are also placed near the drain).qBJ嘉泰姆
- The input capacitor should be near the drain of the up-per MOSFET; the high quality ceramic decoupling capaci-tor can be put close to the VCC and GND pins; the VTTREF decoupling capacitor should be close to the VTTREF pin and GND; the VDDQ and VTT output capacitors should be located right across their output pin as close as pos-sible to the part to minimize parasitic. The input capacitor GND should be close to the output capacitor GND and the lower MOSFET GND.qBJ嘉泰姆
- The drain of the MOSFETs (VIN and PHASE nodes) should be a large plane for heat sinking. And PHASE pinqBJ嘉泰姆
traces are also the return path for UGATE. Connect this pin to the converter’s upper MOSFET source.qBJ嘉泰姆
- The CXSD62115 used ripple mode control. Build the re- sistor divider close to the VFB pin so that the high imped- ance trace is shorter. And the VFB pin traces can’t be closed to the switching signal traces (UGATE, LGATE,BOOT, and PHASE).qBJ嘉泰姆
- The PGND trace should be a separate trace, and inde-pendently go to the source of the low-side MOSFETs forqBJ嘉泰姆
current limit accuracy.qBJ嘉泰姆

Layout ConsiderationqBJ嘉泰姆
- Keep the switching nodes (UGATE, LGATE, BOOT, and PHASE) away from sensitive small signal nodes(VFB,VTTREF, and CS) since these nodes are fast moving signals. Therefore, keep traces to these nodes as short as possible and there should be no other weak signal traces in parallel with theses traces on any layer.qBJ嘉泰姆
- The signals going through theses traces have both high dv/dt and high di/dt, with high peak charging and dis-charging current. The traces from the gate drivers to the MOSFETs (UGATE and LGATE) should be short and wide.qBJ嘉泰姆
- Place the source of the high-side MOSFET and the drain of the low-side MOSFET as close as possible. Minimiz-ing the impedance with wide layout plane between the two pads reduces the voltage bounce of the node.qBJ嘉泰姆

- Decoupling qBJ嘉泰姆

 capacitor, the resistor dividers, boot capacitors, and current limit stetting resistor should beqBJ嘉泰姆

CXSD62115qBJ嘉泰姆

八,相关产品             更多同类产品...... qBJ嘉泰姆

◀ 上一篇:两个低电压降调节器CXSD62114双降压恒定时间同步PWM控制器内部转换MOSFET

返回顶部

下一篇▶:CXSD62116A|B|C电压模式固定300kHz开关频率和同步降压控制器两个电源电压模式

共有条评论 用户名: 密码: 验证码: 匿名发表