目录4J6嘉泰姆

1.产品概述                       2.产品特点4J6嘉泰姆
3.应用范围                       4.产品封装图4J6嘉泰姆
5.电路原理图                   6.产品PCB                   4J6嘉泰姆
7.产品BOM                      8.产品PDF文档 4J6嘉泰姆
9.功能概述                      10.相关产品4J6嘉泰姆

 4J6嘉泰姆

一,产品概述(General Description)   4J6嘉泰姆

        The CXSD61051 is a synchronous step down regulator with CC control from a high voltage input supply. Operating with an input voltage4J6嘉泰姆
range of 8V ～ 30V, the CXSD61051 achieves 3.5A continuous output current with excellent load and line regulation. The switching  frequency is programmable from 100KHz to 500KHz and the synchronous architecture4J6嘉泰姆
provides for highly efficient designs. Current  mode operation provides fast transient response and eases loop stabilization.4J6嘉泰姆

         The CXSD61051 requires a minimum number of readily available standard external components. Other features include cable compensation programmable current limit and thermal shutdown.4J6嘉泰姆

        The CXSD61051 converters are available in the industry standard SOP8-PP packages       4J6嘉泰姆

二.产品特点(Features)4J6嘉泰姆

Wide Input Voltage Range: 8V ～ 30V4J6嘉泰姆

Up to 93% Efficiency4J6嘉泰姆

Programmable Switching Frequency up to 500KHz4J6嘉泰姆

No Loop Compensation Required4J6嘉泰姆

CC/CV control4J6嘉泰姆

Programmable CC Current4J6嘉泰姆

Thermal Shutdown4J6嘉泰姆

Available in SOP8-PP Package4J6嘉泰姆

三,应用范围 (Applications) 4J6嘉泰姆

Car Charger / Adaptor4J6嘉泰姆

LED Driver4J6嘉泰姆

Pre-Regulator for Linear Regulators4J6嘉泰姆

Distributed Power Systems4J6嘉泰姆

Battery ChargerCar Charger / Adaptor4J6嘉泰姆

LED Driver4J6嘉泰姆

Pre-Regulator for Linear Regulators4J6嘉泰姆

Distributed Power Systems4J6嘉泰姆

Battery Charger4J6嘉泰姆

四,产品封装图 (Package)4J6嘉泰姆
4J6嘉泰姆

五,电路原理图4J6嘉泰姆

4J6嘉泰姆

六, 产品PCB4J6嘉泰姆
(略)4J6嘉泰姆
七.产品BOM  4J6嘉泰姆
  (略)4J6嘉泰姆
八.产品PDF文档 4J6嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！4J6嘉泰姆

 4J6嘉泰姆

九,功能概述4J6嘉泰姆

Application Information 4J6嘉泰姆
The CXSD61051 operates by a constant frequency, current mode architecture. The output voltage is set4J6嘉泰姆
by an external divider returned to the FB pin. An error amplifier compares the divided output voltage with4J6嘉泰姆
a reference voltage of 1.21V and adjusts the peak inductor current accordingly. 4J6嘉泰姆
Thermal Protection4J6嘉泰姆
The total power dissipation in CXSD61051 is limited by a thermal protection circuit. When the device4J6嘉泰姆
temperature rises to approximately +160°C, this circuit turns off the output, allowing the IC to cool. The4J6嘉泰姆
thermal protection circuit can protect the device from being damaged by overheating in the event of fault4J6嘉泰姆
conditions. Continuously running the CXSD61051 into thermal shutdown degrades device reliability. 4J6嘉泰姆
Current Limit4J6嘉泰姆
Current limit detection occurs during the off-time by monitoring the current through the low-side switch4J6嘉泰姆
using an external resistor, RLIM. The current limit value is defined by RLIM. If during the off-time the4J6嘉泰姆
current in the low-side switch exceeds the user defined current limit value, the next on-time cycle is4J6嘉泰姆
immediately terminated. Current sensing is achieved by comparing the voltage across the low side FET4J6嘉泰姆
with the voltage across the current limit set resistor RLIM. For example, the current limit value is 4.5A by4J6嘉泰姆
the RLIM =100K. The current limit value rises when the set resistor RLIM rises. The maximum output4J6嘉泰姆
current is set by RLIM: RLIM (kΩ) = 1500 · IMAX (A) / RDS_PMOS (mΩ). 4J6嘉泰姆
Oscillator Frequency4J6嘉泰姆
The CXSD61051 oscillator frequency is set by a single external resistor connected between the RT pin and4J6嘉泰姆
the GND pin. The resistor should be located very close to the device and connected directly to the pins4J6嘉泰姆
of the IC (RT and GND). An internal amplifier holds the RT pin at a fixed voltage typically 0.6V. The4J6嘉泰姆
oscillator frequency rises when the resistor RT falls. To determine the timing resistance for a given4J6嘉泰姆
switching frequency, use the equation below:4J6嘉泰姆
RT(kΩ)= 22000 /fOSC(kHz) 4J6嘉泰姆
Setting Output Voltage4J6嘉泰姆
The output voltage is set with a resistor divider from the output node to the FB pin. It is recommended to4J6嘉泰姆
use divider resistors with 1% tolerance or better. To improve efficiency at very light loads consider using4J6嘉泰姆
larger value resistors. If the values are too high the regulator is more susceptible to noise and voltage4J6嘉泰姆
errors from the FB input current are noticeable. For most applications, a resistor in the 10kΩ to 1MΩ4J6嘉泰姆
range is suggested for R3. R2 is then given by:4J6嘉泰姆
R2 = R3 · [(VOUT / VREF) – 1]4J6嘉泰姆
where VREF is 1.21V.4J6嘉泰姆
Output Cable Resistance Compensation4J6嘉泰姆
To compensate for resistive voltage drop across the charger's output cable, the CXSD61051 integrates a4J6嘉泰姆
simple, user-programmable cable voltage drop compensation using the impedance at the FB pin.4J6嘉泰姆
Choose the proper feedback resistance values for cable compensation refer to the curve in Figure 1.4J6嘉泰姆
The delta VOUT voltage rises when the feedback resistance R3 value rises, use the equation below4J6嘉泰姆
十,相关产品              更多同类产品......4J6嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表